SnowyPlover

Design options

To compare schemes in one animation, put each option on its own Rhino layer. Design Option Timeline decides which option is visible at each t, and Apply Design Option switches the layers.

Set up the layers

There are two ways to tell the components which layers are the options:

Wire it

Connect the same Panel to the options input of both components, so they agree on the list. Then wire visibility across and click Apply Design Option's button so it reads Active.

Optionst0.4Design Option Timeline: Map a normalized t (0..1) to design options stored on Rhino layers. Hard cut between options, with optional blank gaps. Options input: ONE layer -> its direct sub layers become the options. TWO OR MORE layers -> each layer is one option. This component does not modify the Rhino document. Use Apply Design Option to change layer visibility.Design Option Timelineoptions (L) Text · list Option layers. One parent layer (its sub layers are the options) or a list of layer full paths / names.optionst Number · item Normalized time parameter in [0,1]tdurations (D) Number · list optional Relative duration weights for each option in the sequence. If left empty, all options are equal length. Missing or non-positive values default to 1.0.durationsgap (G) Number · item default 0.0 Blank gap weight between options, in the same unit as durations. 0 = pure hard cut. Right-click to add a gap at the start / end.gapvisibility (V) Boolean · list Visibility per option. Connect to Apply Design Option.visibilityApply Design Option: Show / hide design option layers in the Rhino document using the visibility list from Design Option Timeline. Connect the SAME options input as Design Option Timeline. Click the button to switch it on or off. Original layer visibility is recorded when switched on and restored when switched off (right-click to change).Apply Design Optionoptions (L) Text · list Option layers. Use the same input as Design Option Timeline.optionsvisibility (V) Boolean · list Visibility per option, from Design Option Timeline.visibilitystatus (S) Text · item StatusstatusInactive
Design Option Timeline only computes; Apply Design Option is the one that changes the Rhino layers.

When you click the button to switch it off, Apply Design Option puts every layer back the way it was when you switched it on. Right-click it to turn that off, or to restore the layers right away.

Timing the options

Animating inside one option

The progress output has one value per option: 0 before its slot, 0 to 1 during it, and 1 after it. Use it to animate something that belongs to one option, for example arrows that draw themselves only while option B is on screen. Pick the option with List Item, or connect the whole list to an Event Timeline and choose with its index input.

Optionst0.55Design Option Timeline: Map a normalized t (0..1) to design options stored on Rhino layers. Hard cut between options, with optional blank gaps. Options input: ONE layer -> its direct sub layers become the options. TWO OR MORE layers -> each layer is one option. This component does not modify the Rhino document. Use Apply Design Option to change layer visibility.Design Option Timelineoptions (L) Text · list Option layers. One parent layer (its sub layers are the options) or a list of layer full paths / names.optionst Number · item Normalized time parameter in [0,1]tprogress (P) Number · list Progress per sequence item: 0 before its slot, 0..1 inside, 1 after. Use it to drive animations that belong to one option (e.g. arrows). Right-click 'Progress: Null Outside Slot' to output null instead of 0 / 1 outside the slot.progressEvent Timeline: Split a normalized t (0..1) into events. Each event has its own 0..1 output. t can be master T, Design Option Timeline progress, or an event output of another Event Timeline. duration (seconds) is only used to display and snap the timeline in seconds. Drag bars to edit, +/- to add or remove events, hold Shift while dragging to disable snapping.Event Timelinet Number · list optional Normalized time parameter in [0,1]. One value, or a list (e.g. progress) picked by index. Null t -> all events output null.tindex (I) Integer · item default 0 Item to pick when t / duration are lists. Default 0.indexevent 1 (E1) Number · item t of event 1 [0..1]event 1event 2 (E2) Number · item t of event 2 [0..1]event 2option1Animate Arrow: Animate arrows based on provided curvesAnimate Arrowcurves (C) Curve · list Reference Planar Curves to animate Arrowscurvest Number · item Normalized time parameter in [0,1]. If t is null (e.g. Design Option Timeline with 'Null Outside Slot'), nothing is output.t

Right-click Design Option Timeline and choose Progress: Null Outside Slot to output nothing outside the slot. Components such as Animate Arrow then draw nothing at all while their option is hidden.

Blending between options

Design Option Timeline always cuts hard from one option to the next, because a layer is either on or off. For a crossfade, export overlapping parts of the same camera move once per option, and join them with a crossfade in Join Clips. The full recipe, with diagrams, is in Crossfade between two design options.